How to build an ambient lamp out of bulk packaging foamThis lamp is basically a stack of packaging foam that seems to glow fromthe inside and contrary to what one would expect gives off a warm, cosylight. It consists of a loose stack of rough cut packaging foam (dozensof motherboards were packaged in it) but can be built out of anythingthat is only vaguely transparent. TVBNOW 含有熱門話題，最新最快電視，軟體，遊戲，電影，動漫及日常生活及興趣交流等資訊。/ F' W4 F& }8 U) C2 }/ ?
) u- s! x3 `' n. Q" G R4 ]
The basic principle is this: Take a stack of packaging foamsheets, cut a hole into it, stick a light bulb in and you're done.However, one important thing is VENTILATION, which is the focus of thelast step of this instructable.
) y/ d" `' P- p' E9 |7 A0 t3 O& a9 A2 r& Y
I will not give precise dimensions but explain my considerations thatled me to the result shown below and will enable you to built your lampto your liking.公仔箱論壇0 ]0 ~+ _3 u0 N0 w
TVBNOW 含有熱門話題，最新最快電視，軟體，遊戲，電影，動漫及日常生活及興趣交流等資訊。/ n) G* L; [# q) M
Please don't hesitate to contact me if you have any questions or comments.7 O/ Z$ F( v N% n
tvb now,tvbnow,bttvb! Q5 E4 |7 M$ A0 o% H0 e W
 TVBNOW 含有熱門話題，最新最快電視，軟體，遊戲，電影，動漫及日常生活及興趣交流等資訊。& `' S" Y/ Y j; V
3 I( X* p0 r7 @: Z% `2 f% G% S! v. ]
. M' o- e- U# m! Dtvb now,tvbnow,bttvb2 ^: D3 {# F$ L& G4 ^& C
( ]/ M H& k3 d) i! x$ a2 itvb now,tvbnow,bttvbos.tvboxnow.com7 j& R7 x8 H0 } b. L4 _5 M
& C7 F4 c( ^/ b/ d' n) D3 A6 Y2 K公仔箱論壇
) X/ x5 O& F, |' t7 mTVBNOW 含有熱門話題，最新最快電視，軟體，遊戲，電影，動漫及日常生活及興趣交流等資訊。
0 l, Y# ~4 H+ d! Y: F8 M1 Uos.tvboxnow.com tvb now,tvbnow,bttvb& u& f% T1 F6 S! e9 v
Materials and Toolsos.tvboxnow.com/ X' f- D6 y$ @6 ^
For this Project you will need:Materials:Packaging foam or anything you think might work: - not too sensitive to heat. - try to do a test whether you like the tint the light has afterit has passed through it - amount: enough to create a stack of your liking that isable to house the fixture, the bulb, some free space above the bulb anda couple of top layer…6 l+ w+ X* a0 D% D6 n
公仔箱論壇* D) A4 F! U+ a1 p
) Q1 p, r4 }- n0 kos.tvboxnow.comSome considerations before going ahead
& v% l$ `7 a0 y& A1 G3 z8 H* h8 Qos.tvboxnow.comTo find out how big i wanted the hole for the lamp, I held the lampagainst some sheets of foam and was happy with a thickness about thewidth of my hand. Luckily this happened to work with the amount of space needed for thelamp itself, since the foam must not touch it. Luckily the height of the stack was just enough to house the fixture,the fixing and still need en…
" d5 |6 B8 O0 ltvb now,tvbnow,bttvb
6 D3 s1 T$ f# s2 ?* Q* D; s9 @公仔箱論壇
, P# g! f% t& e! Q/ xtvb now,tvbnow,bttvbHollowing out
; W0 O9 K8 Q/ G6 M' ^os.tvboxnow.comAfter this, I started cutting the hole to hold the fixture snuggly andused the ring which is normally used to hold the lampshade to fix it tothe base (image 1 and 2). Then I used a cup to cut the holes in the center of the remainingsheets (image 3), except for about ten which would be the top. Iactually made a stencil out of cardboard first to help me mark thepos…
. Z( k1 e5 d. \, r5 }. kos.tvboxnow.com
) }: n4 q3 g% b/ n/ g* w公仔箱論壇 Ventilation
& o( _( j3 U6 e8 }9 G0 K6 b3 K* y" VTVBNOW 含有熱門話題，最新最快電視，軟體，遊戲，電影，動漫及日常生活及興趣交流等資訊。In principle this lamp is now done, and back when i built itI switched it on for the first time and let it on for a couple ofminutes, excited about the look. Big mistake! The heat of the 22 Watts bulb started melting the foamalmost immediately. That's when I switched it off and started thinkingabout ventilation. Since the foam is such a good insulator the heat … |
發表於 2010-5-23 08:51 PM
| 
